How to Use the nmap Command

Nmap is a powerful network scanning tool for security audits and penetration testing. It is one of the essential tools used by network administrators to troubleshooting network connectivity issues and port scanning .

Nmap can also detect the Mac address, OS type , service version, and much more.

This article explains the basics of how to use the nmap command to perform various network tasks.

Installing Nmap #

Nmap is a multi-platform program that can be installed on all major operating systems. It was initially released as a Linux-only tool, and later it was ported to other systems such as BSD, Windows, and macOS.

If you prefer a GUI over the command line, Nmap also has a graphical user interface called Zenmap .

The official binary packages are available for download from the Nmap download page .

The installation procedure is straightforward and varies according to your operating system.

Installing Nmap on Ubuntu and Debian #

Nmap is available from the default Ubuntu and Debian repositories. To install it, run:

sudo apt updatesudo apt install nmap

Installing Nmap on CentOS and Fedora #

On CentOS and other Red Hat derivatives run:

sudo dnf install nmap

Installing Nmap on macOS #

macOS users can install Nmap by downloading the “.dmg” installation package from the Nmap site or via Homebrew:

brew install nmap

Installing Nmap on Windows #

The Windows version of Nmap has some limitations, and it is generally a little slower than the UNIX version.

The easiest option to install Nmap on Windows is to download and run the self-installation exe file.

You can run Nmap on Windows either from the command line or by launching the Zenmap program. For more information about how to use Nmap on Windows, check the post-install usage instructions .

Using Nmap #

Nmap is typically used to audit network security, network mapping, identify open ports, and search for online devices.

The simplified syntax of the nmap command is as follows:

nmap [Options] [Target… ] 

The most basic example of using Nmap is to scan a single target as a standard user without specifying any options:

nmap scanme.nmap.org

When invoked as a non-root user that does not have raw packet privileges, nmap runs TCP connect scan. The (-sT) is turned on by default in unprivileged mode.

The output will look something like this, including basic information about the scan and a list of open and filtered TCP ports.

Starting Nmap 7.91 ( https://nmap.org ) at 2020-12-16 20:19 CET Nmap scan report for cast.lan (192.168.10.121) Host is up (0.048s latency). Not shown: 981 closed ports PORT STATE SERVICE 21/tcp open ftp 22/tcp open ssh 25/tcp open smtp 53/tcp open domain 80/tcp open http 110/tcp open pop3 143/tcp open imap 443/tcp open https 587/tcp open submission 993/tcp open imaps 995/tcp open pop3s 1025/tcp open NFS-or-IIS 1080/tcp open socks 8080/tcp open http-proxy 8081/tcp open blackice-icecap Nmap done: 1 IP address (1 host up) scanned in 1.78 seconds 

The most popular scan option is the TCP SYN scan (-sS) that is faster than the connect option and works against all compliant TCP stacks.

-sS is turned on by default when nmap is invoked as a user with administrative privileges:

sudo nmap 192.168.10.121

For more detailed output, use the increase the verbosity with -v or -vv:

sudo nmap -vv 192.168.10.121

To perform a UDP scan, invoke the command with the (-sU) option as a root user:

sudo nmap -sU 192.168.10.121

For a complete list of port scanning methods, visit the Nmap documentation page .

Nmap also supports IPv6 addresses. To specify an IPv6 host use the -6 option:

sudo nmap -6 fd12:3456:789a:1::1

Specifying Target Hosts #

Nmap treats all arguments that are not options as target hosts.

The simplest option is to pass one or more target addresses or domain names:

nmap 192.168.10.121 host.to.scan

You can use the CIDR notation to specify a network range:

nmap 192.168.10.0/24

To specify an octet range use the dash character. For example, to scan 192.168.10.1, 192.168.11.1, and 192.168.12.1:

nmap 192.168.10-12.1

Another character you can use to specify the targets is the comma. The following command targets the same hosts as the one above:

nmap 192.168.10,11,12.1

You can combine all forms:

nmap 10.8-10.10,11,12.0/28 192.168.1-2.100,101

To make sure you specified the correct hosts before scanning, use the list scan option (-sL), which only lists the targets without running a scan:

nmap -sL 10.8-10.10,11,12.0/28 192.168.1-2.100,101

If you want to exclude targets that are included in the range you specified, use the --exclude option:

nmap 10.8-10.10,11,12.0/28 --exclude 10.10.12.12

Specifying and Scanning Ports #

By default, Nmap performs a quick scan for the 1000 most popular ports. These ports are not the first 1000 consecutive ports, but the 1000 most commonly used ports ranging from 1 to 65389.

To scan for all ports from 1 through 65535, use the -p- option:

nmap -p- 192.168.10.121

Each port can be in one of the following states:

• open - The program running on the port responds to request.
• closed - No program runs on the port, and the host reply to requests.
• filtered - The host doesn't reply to the request.

Ports and port ranges are specified with the -p option.

For example, to scan only port 443, you would use the following command:

nmap -p 443 192.168.10.121

To specify more than one port, separate the target ports with a comma:

nmap -p 80,443 192.168.10.121

Port ranges can be specified with the dash symbol. For example, to scan all UDP ports ranging from 1 to 1024, you would run:

sudo nmap -sU -p 1-1024 192.168.10.121

All combined:

nmap -p 1-1024,8080,9000 192.168.10.121

Ports can also be specified using the port name. For example, to scan for port 22, ssh, you can use:

nmap -p ssh 192.168.10.121

Ping Scanning #

To perform a ping scanning or host discovery, invoke the nmap command with the -sn option:

sudo nmap -sn 192.168.10.0/24

The -sn option tells Nmap only to discover online hosts and not to do a port scan. This is useful when you want to quickly determine which of the specified host are up and running.

Disabling DNS Name Resolution #

Nmap's default behavior is to perform reverse-DNS resolution for each discovered host, which increases the scan time.

When scanning large networks, it is a good idea to disable reverse-DNS resolution and speed up the scans. To do that, invoke the command with the -n option:

sudo nmap -n 192.168.10.0/16

OS, Service and Version Detection #

Nmap can detect the remote host operating system using TCP/IP stack fingerprinting. To run OS detection, invoke the command with the -O option:

sudo nmap -O scanme.nmap.org

If Nmap can detect the host OS, it will print something like below:

… Device type: general purpose Running: Linux 5.X OS CPE: cpe:/o:linux:linux_kernel:5 OS details: Linux 5.0 - 5.4 Network Distance: 18 hops OS detection performed. Please report any incorrect results at https://nmap.org/submit/ . Nmap done: 1 IP address (1 host up) scanned in 26.47 seconds 

Typically, system services listen on standard ports that are well known and reserved for them. For example, if port 22 that corresponds to the SSH service is open, you'll assume that an SSH server runs on the host. However, you cannot be absolutely sure because people can run services on whatever ports they want.

With service and version detection, Nmap will show you what program listens on the port and the program version.

To scan for service and version, use the -sV option:

sudo nmap -sV scanme.nmap.org

… PORT STATE SERVICE VERSION 19/tcp filtered chargen 22/tcp open ssh OpenSSH 6.6.1p1 Ubuntu 2ubuntu2.13 (Ubuntu Linux; protocol 2.0) 80/tcp open http Apache httpd 2.4.7 ((Ubuntu)) 135/tcp filtered msrpc 139/tcp filtered netbios-ssn 445/tcp filtered microsoft-ds 9929/tcp open nping-echo Nping echo 31337/tcp open tcpwrapped Service Info: OS: Linux; CPE: cpe:/o:linux:linux_kernel… 

You can also scan for OS, Versions, and run traceroute in one command using the -A option:

sudo nmap -A 192.168.10.121

Nmap Output #

By default, Nmap prints the information to standard output (stdout).

If you scan a large network or need the information for later usage, you can save the output to a file.

Nmap provides several output types. To save the output in normal format, use the -oN option followed by the file name:

sudo nmap -sU -p 1-1024 192.168.10.121 -oN output.txt

The most popular option is to save the output in XML format. To do so, use the -oX option:

sudo nmap -sU -p 1-1024 192.168.10.121 -oX output.xml

Another useful format is the grepable output, which can be parsed with the standard Unix tools like grep , awk and cut . The grepable output is specified with the -oG option:

sudo nmap -sU -p 1-1024 192.168.10.121 -oG output

Nmap Scripting Engine #

One of the most powerful features of Nmap is its scripting engine. Nmap ships with hundreds of scrips , and you can also write your own scrips in the Lua language.

You can use scrips to detect malware and backdoors, perform brute-force attacks, and more.

For example, to check if a given host is compromised you can use:

nmap -sV --script http-malware-host scanme.nmap.org

Conclusion #

Nmap is an open-source tool that is used primarily by network administrators to discover host and scan ports.

Please note that in some countries, it is not legal to scan networks without authorization.

If you have any questions or remarks, please leave a comment below.